1 | /*==============================================================================
|
---|
2 | * NETWORK CONFIGURATION
|
---|
3 | *
|
---|
4 | * You must configure your particular hardware. Follow the steps below.
|
---|
5 | *
|
---|
6 | * Currently StandardFirmataEthernet is configured as a client. An option to
|
---|
7 | * configure as a server may be added in the future.
|
---|
8 | *============================================================================*/
|
---|
9 |
|
---|
10 | // STEP 1 [REQUIRED]
|
---|
11 | // Uncomment / comment the appropriate set of includes for your hardware (OPTION A or B)
|
---|
12 | // Option A is enabled by default.
|
---|
13 |
|
---|
14 | /*
|
---|
15 | * OPTION A: Configure for Arduino Ethernet board or Arduino Ethernet shield (or clone)
|
---|
16 | *
|
---|
17 | * To configure StandardFirmataEthernet to use the original WIZ5100-based
|
---|
18 | * ethernet shield or Arduino Ethernet uncomment the WIZ5100_ETHERNET define below
|
---|
19 | */
|
---|
20 | #define WIZ5100_ETHERNET
|
---|
21 |
|
---|
22 | #ifdef WIZ5100_ETHERNET
|
---|
23 | #include <SPI.h>
|
---|
24 | #include <Ethernet.h>
|
---|
25 | EthernetClient client;
|
---|
26 | #endif
|
---|
27 |
|
---|
28 | /*
|
---|
29 | * OPTION B: Configure for Arduin Yun
|
---|
30 | *
|
---|
31 | * The Ethernet port on the Arduino Yun board can be used with Firmata in this configuration.
|
---|
32 | *
|
---|
33 | * To execute StandardFirmataEthernet on Yun uncomment the YUN_ETHERNET define below and make
|
---|
34 | * sure the WIZ5100_ETHERNET define (above) is commented out.
|
---|
35 | *
|
---|
36 | * On Yun there's no need to configure local_ip and mac address as this is automatically
|
---|
37 | * configured on the linux-side of Yun.
|
---|
38 | */
|
---|
39 | //#define YUN_ETHERNET
|
---|
40 |
|
---|
41 | #ifdef YUN_ETHERNET
|
---|
42 | #include <Bridge.h>
|
---|
43 | #include <YunClient.h>
|
---|
44 | YunClient client;
|
---|
45 | #endif
|
---|
46 |
|
---|
47 |
|
---|
48 | // STEP 2 [REQUIRED for all boards and shields]
|
---|
49 | // replace with IP of the server you want to connect to, comment out if using 'remote_host'
|
---|
50 | #define remote_ip IPAddress(10, 0, 0, 3)
|
---|
51 | // *** REMOTE HOST IS NOT YET WORKING ***
|
---|
52 | // replace with hostname of server you want to connect to, comment out if using 'remote_ip'
|
---|
53 | // #define remote_host "server.local"
|
---|
54 |
|
---|
55 | // STEP 3 [REQUIRED unless using Arduin Yun]
|
---|
56 | // Replace with the port that your server is listening on
|
---|
57 | #define remote_port 3030
|
---|
58 |
|
---|
59 | // STEP 4 [REQUIRED unless using Arduino Yun OR if not using DHCP]
|
---|
60 | // Replace with your board or ethernet shield's IP address
|
---|
61 | // Comment out if you want to use DHCP
|
---|
62 | #define local_ip IPAddress(10, 0, 0, 15)
|
---|
63 |
|
---|
64 | // STEP 5 [REQUIRED unless using Arduino Yun]
|
---|
65 | // replace with ethernet shield mac. Must be unique for your network
|
---|
66 | const byte mac[] = {0x90, 0xA2, 0xDA, 0x00, 0x53, 0xE5};
|
---|
67 |
|
---|
68 | /*==============================================================================
|
---|
69 | * CONFIGURATION ERROR CHECK (don't change anything here)
|
---|
70 | *============================================================================*/
|
---|
71 |
|
---|
72 | #if !defined WIZ5100_ETHERNET && !defined YUN_ETHERNET
|
---|
73 | #error "you must define either WIZ5100_ETHERNET or YUN_ETHERNET in ethernetConfig.h"
|
---|
74 | #endif
|
---|
75 |
|
---|
76 | #if defined remote_ip && defined remote_host
|
---|
77 | #error "cannot define both remote_ip and remote_host at the same time in ethernetConfig.h"
|
---|
78 | #endif
|
---|
79 |
|
---|
80 | /*==============================================================================
|
---|
81 | * PIN IGNORE MACROS (don't change anything here)
|
---|
82 | *============================================================================*/
|
---|
83 |
|
---|
84 | // ignore SPI pins, pin 10 (Ethernet SS) and pin 4 (SS for SD-Card on Ethernet shield)
|
---|
85 | #define IS_IGNORE_ETHERNET_SHIELD(p) ((IS_PIN_SPI(p) || (p) == 4) || (p) == 10)
|
---|