
#ifndef _PHY_REG_
#define _PHY_REG_

#include <target_syssvc.h>

/* Generic MII registers */
#define MII_BMCR                0x00    /* Basic mode control register        */
#define MII_BMSR                0x01    /* Basic mode status register         */
#define MII_PHYSID1             0x02    /* PHYS ID 1                          */
#define MII_PHYSID2             0x03    /* PHYS ID 2                          */
#define MII_ADVERTISE           0x04    /* Advertisement control reg          */
#define MII_LPA                 0x05    /* Link partner ability reg           */
#define MII_EXPANSION           0x06    /* Expansion register                 */
#define MII_CTRL1000            0x09    /* 1000BASE-T control                 */
#define MII_STAT1000            0x0a    /* 1000BASE-T status                  */
#define MII_ESTATUS             0x0f    /* Extended Status                    */
#define MII_SPECIFICCR          0x10    /* Specific control register          */
#define MII_DCOUNTER            0x12    /* Disconnect counter                 */
#define MII_FCSCOUNTER          0x13    /* False carrier counter              */
#define MII_NWAYTEST            0x14    /* N-way auto-neg test reg            */
#define MII_RERRCOUNTER         0x15    /* Receive error counter              */
#define MII_SREVISION           0x16    /* Silicon revision                   */
#define MII_RESV1               0x17    /* Reserved...                        */
#define MII_LBRERROR            0x18    /* Lpback, rx, bypass error           */
#define MII_PHYADDR             0x19    /* PHY address                        */
#define MII_RESV2               0x1a    /* Reserved...                        */
#define MII_TPISTATUS           0x1b    /* TPI status for 10mbps              */
#define MII_NCONFIG             0x1c    /* Network interface config           */

/* Basic mode control register. */
#define BMCR_RESV               0x003f  /* Unused...                          */
#define BMCR_SPEED1000          0x0040  /* MSB of Speed (1000)                */
#define BMCR_CTST               0x0080  /* Collision test                     */
#define BMCR_FULLDPLX           0x0100  /* Full duplex                        */
#define BMCR_ANRESTART          0x0200  /* Auto negotiation restart           */
#define BMCR_ISOLATE            0x0400  /* Disconnect DP83840 from MII        */
#define BMCR_PDOWN              0x0800  /* Powerdown the DP83840              */
#define BMCR_ANENABLE           0x1000  /* Enable auto negotiation            */
#define BMCR_SPEED100           0x2000  /* Select 100Mbps                     */
#define BMCR_LOOPBACK           0x4000  /* TXD loopback bits                  */
#define BMCR_RESET              0x8000  /* Reset the DP83840                  */
#define BMCR_SPEED10            0x0000  /* Select 10Mbps                      */

/* Basic mode status register. */
#define BMSR_ERCAP              0x0001  /* Ext-reg capability                 */
#define BMSR_JCD                0x0002  /* Jabber detected                    */
#define BMSR_LSTATUS            0x0004  /* Link status                        */
#define BMSR_ANEGCAPABLE        0x0008  /* Able to do auto-negotiation        */
#define BMSR_RFAULT             0x0010  /* Remote fault detected              */
#define BMSR_ANEGCOMPLETE       0x0020  /* Auto-negotiation complete          */
#define BMSR_RESV               0x00c0  /* Unused...                          */
#define BMSR_ESTATEN            0x0100	/* Extended Status in R15             */
#define BMSR_100HALF2           0x0200  /* Can do 100BASE-T2 HDX              */
#define BMSR_100FULL2           0x0400  /* Can do 100BASE-T2 FDX              */
#define BMSR_10HALF             0x0800  /* Can do 10mbps, half-duplex         */
#define BMSR_10FULL             0x1000  /* Can do 10mbps, full-duplex         */
#define BMSR_100HALF            0x2000  /* Can do 100mbps, half-duplex        */
#define BMSR_100FULL            0x4000  /* Can do 100mbps, full-duplex        */
#define BMSR_100BASE4           0x8000  /* Can do 100mbps, 4k packets         */

/* Advertisement control register. */
#define ADVERTISE_SLCT          0x001f  /* Selector bits                      */
#define ADVERTISE_CSMA          0x0001  /* Only selector supported            */
#define ADVERTISE_10HALF        0x0020  /* Try for 10mbps half-duplex         */
#define ADVERTISE_1000XFULL     0x0020  /* Try for 1000BASE-X full-duplex     */
#define ADVERTISE_10FULL        0x0040  /* Try for 10mbps full-duplex         */
#define ADVERTISE_1000XHALF     0x0040  /* Try for 1000BASE-X half-duplex     */
#define ADVERTISE_100HALF       0x0080  /* Try for 100mbps half-duplex        */
#define ADVERTISE_1000XPAUSE    0x0080  /* Try for 1000BASE-X pause           */
#define ADVERTISE_100FULL       0x0100  /* Try for 100mbps full-duplex        */
#define ADVERTISE_1000XPSE_ASYM 0x0100  /* Try for 1000BASE-X asym pause      */
#define ADVERTISE_100BASE4      0x0200  /* Try for 100mbps 4k packets         */
#define ADVERTISE_PAUSE_CAP     0x0400  /* Try for pause                      */
#define ADVERTISE_PAUSE_ASYM    0x0800  /* Try for asymetric pause            */
#define ADVERTISE_RESV          0x1000  /* Unused...                          */
#define ADVERTISE_RFAULT        0x2000  /* Say we can detect faults           */
#define ADVERTISE_LPACK         0x4000  /* Ack link partners response         */
#define ADVERTISE_NPAGE         0x8000  /* Next page bit                      */

/* 1000BASE-T Control register */
#define ADVERTISE_1000FULL      0x0200  /* Advertise 1000BASE-T full duplex   */
#define ADVERTISE_1000HALF      0x0100  /* Advertise 1000BASE-T half duplex   */

/* Link partner ability register. */
#define LPA_SLCT                0x001f  /* Same as advertise selector         */
#define LPA_10HALF              0x0020  /* Can do 10mbps half-duplex          */
#define LPA_1000XFULL           0x0020  /* Can do 1000BASE-X full-duplex      */
#define LPA_10FULL              0x0040  /* Can do 10mbps full-duplex          */
#define LPA_1000XHALF           0x0040  /* Can do 1000BASE-X half-duplex      */
#define LPA_100HALF             0x0080  /* Can do 100mbps half-duplex         */
#define LPA_1000XPAUSE          0x0080  /* Can do 1000BASE-X pause            */
#define LPA_100FULL             0x0100  /* Can do 100mbps full-duplex         */
#define LPA_1000XPAUSE_ASYM     0x0100  /* Can do 1000BASE-X pause asym       */
#define LPA_100BASE4            0x0200  /* Can do 100mbps 4k packets          */
#define LPA_PAUSE_CAP           0x0400  /* Can pause                          */
#define LPA_PAUSE_ASYM          0x0800  /* Can pause asymetrically            */
#define LPA_RESV                0x1000  /* Unused...                          */
#define LPA_RFAULT              0x2000  /* Link partner faulted               */
#define LPA_LPACK               0x4000  /* Link partner acked us              */
#define LPA_NPAGE               0x8000  /* Next page bit                      */

#define LPA_DUPLEX              (LPA_10FULL  | LPA_100FULL)
#define LPA_100                 (LPA_100FULL | LPA_100HALF | LPA_100BASE4)

/* 1000BASE-T Status register */
#define LPA_1000LOCALRXOK       0x2000  /* Link partner local receiver status  */
#define LPA_1000REMRXOK         0x1000  /* Link partner remote receiver status */
#define LPA_1000FULL            0x0800  /* Link partner 1000BASE-T full duplex */
#define LPA_1000HALF            0x0400  /* Link partner 1000BASE-T half duplex */

/* Expansion register for auto-negotiation. */
#define EXPANSION_NWAY          0x0001  /* Can do N-way auto-nego             */
#define EXPANSION_LCWP          0x0002  /* Got new RX page code word          */
#define EXPANSION_ENABLENPAGE   0x0004  /* This enables npage words           */
#define EXPANSION_NPCAPABLE     0x0008  /* Link partner supports npage        */
#define EXPANSION_MFAULTS       0x0010  /* Multiple faults detected           */
#define EXPANSION_RESV          0xffe0  /* Unused...                          */

#define ESTATUS_1000_TFULL      0x2000  /* Can do 1000BT Full                 */
#define ESTATUS_1000_THALF      0x1000  /* Can do 1000BT Half                 */

/* Specific control register */
#define SPECIFICCR_CROSS_MASK   0x0060  /* Crossover mode mask                */
#define SPECIFICCR_CROSS_MDI    0x0000  /* Manual MDI configuration           */
#define SPECIFICCR_CROSS_MDIX   0x0020  /* Manual MDIX configuration          */
#define SPECIFICCR_CROSS_AUTO   0x0060  /* Enable automatic crossover         */
#define SPECIFICCR_INT_DISABLE  0x1000  /* Interrupt Disable                  */

/* Externded PHY Specific Control Register */
#define NWAYTEST_RGMII_RTC      0x0080  /* RGMII Receive Timing Control       */
#define NWAYTEST_RGMII_TTC      0x0002  /* RGMII Transmit Timing Control      */

#endif /* _PHY_REG_ */
