[224] | 1 | /*
|
---|
| 2 | Firmata is a generic protocol for communicating with microcontrollers
|
---|
| 3 | from software on a host computer. It is intended to work with
|
---|
| 4 | any host computer software package.
|
---|
| 5 |
|
---|
| 6 | To download a host software package, please clink on the following link
|
---|
| 7 | to open the list of Firmata client libraries your default browser.
|
---|
| 8 |
|
---|
| 9 | https://github.com/firmata/arduino#firmata-client-libraries
|
---|
| 10 |
|
---|
| 11 | Copyright (C) 2006-2008 Hans-Christoph Steiner. All rights reserved.
|
---|
| 12 | Copyright (C) 2010-2011 Paul Stoffregen. All rights reserved.
|
---|
| 13 | Copyright (C) 2009 Shigeru Kobayashi. All rights reserved.
|
---|
| 14 | Copyright (C) 2009-2016 Jeff Hoefs. All rights reserved.
|
---|
| 15 |
|
---|
| 16 | This library is free software; you can redistribute it and/or
|
---|
| 17 | modify it under the terms of the GNU Lesser General Public
|
---|
| 18 | License as published by the Free Software Foundation; either
|
---|
| 19 | version 2.1 of the License, or (at your option) any later version.
|
---|
| 20 |
|
---|
| 21 | See file LICENSE.txt for further informations on licensing terms.
|
---|
| 22 |
|
---|
| 23 | Last updated by Jeff Hoefs: January 10th, 2016
|
---|
| 24 | */
|
---|
| 25 |
|
---|
| 26 | /*
|
---|
| 27 | README
|
---|
| 28 |
|
---|
| 29 | StandardFirmataPlus adds additional features that may exceed the Flash and
|
---|
| 30 | RAM sizes of Arduino boards such as ATMega328p (Uno) and ATMega32u4
|
---|
| 31 | (Leonardo, Micro, Yun, etc). It is best to use StandardFirmataPlus with higher
|
---|
| 32 | memory boards such as the Arduino Mega, Arduino Due, Teensy 3.0/3.1/3.2.
|
---|
| 33 |
|
---|
| 34 | All Firmata examples that are appended with "Plus" add the following features:
|
---|
| 35 |
|
---|
| 36 | - Ability to interface with serial devices using UART, USART, or SoftwareSerial
|
---|
| 37 | depending on the capatilities of the board.
|
---|
| 38 |
|
---|
| 39 | At the time of this writing, StandardFirmataPlus will still compile and run
|
---|
| 40 | on ATMega328p and ATMega32u4-based boards, but future versions of this sketch
|
---|
| 41 | may not as new features are added.
|
---|
| 42 | */
|
---|
| 43 |
|
---|
| 44 | #include <Servo.h>
|
---|
| 45 | #include <Wire.h>
|
---|
| 46 | #include <Firmata.h>
|
---|
| 47 |
|
---|
| 48 | #include "utility/SerialFirmata.h"
|
---|
| 49 |
|
---|
| 50 | #define I2C_WRITE B00000000
|
---|
| 51 | #define I2C_READ B00001000
|
---|
| 52 | #define I2C_READ_CONTINUOUSLY B00010000
|
---|
| 53 | #define I2C_STOP_READING B00011000
|
---|
| 54 | #define I2C_READ_WRITE_MODE_MASK B00011000
|
---|
| 55 | #define I2C_10BIT_ADDRESS_MODE_MASK B00100000
|
---|
| 56 | #define I2C_END_TX_MASK B01000000
|
---|
| 57 | #define I2C_STOP_TX 1
|
---|
| 58 | #define I2C_RESTART_TX 0
|
---|
| 59 | #define I2C_MAX_QUERIES 8
|
---|
| 60 | #define I2C_REGISTER_NOT_SPECIFIED -1
|
---|
| 61 |
|
---|
| 62 | // the minimum interval for sampling analog input
|
---|
| 63 | #define MINIMUM_SAMPLING_INTERVAL 1
|
---|
| 64 |
|
---|
| 65 |
|
---|
| 66 | /*==============================================================================
|
---|
| 67 | * GLOBAL VARIABLES
|
---|
| 68 | *============================================================================*/
|
---|
| 69 |
|
---|
| 70 | #ifdef FIRMATA_SERIAL_FEATURE
|
---|
| 71 | SerialFirmata serialFeature;
|
---|
| 72 | #endif
|
---|
| 73 |
|
---|
| 74 | /* analog inputs */
|
---|
| 75 | int analogInputsToReport = 0; // bitwise array to store pin reporting
|
---|
| 76 |
|
---|
| 77 | /* digital input ports */
|
---|
| 78 | byte reportPINs[TOTAL_PORTS]; // 1 = report this port, 0 = silence
|
---|
| 79 | byte previousPINs[TOTAL_PORTS]; // previous 8 bits sent
|
---|
| 80 |
|
---|
| 81 | /* pins configuration */
|
---|
| 82 | byte portConfigInputs[TOTAL_PORTS]; // each bit: 1 = pin in INPUT, 0 = anything else
|
---|
| 83 |
|
---|
| 84 | /* timer variables */
|
---|
| 85 | unsigned long currentMillis; // store the current value from millis()
|
---|
| 86 | unsigned long previousMillis; // for comparison with currentMillis
|
---|
| 87 | unsigned int samplingInterval = 19; // how often to run the main loop (in ms)
|
---|
| 88 |
|
---|
| 89 | /* i2c data */
|
---|
| 90 | struct i2c_device_info {
|
---|
| 91 | byte addr;
|
---|
| 92 | int reg;
|
---|
| 93 | byte bytes;
|
---|
| 94 | byte stopTX;
|
---|
| 95 | };
|
---|
| 96 |
|
---|
| 97 | /* for i2c read continuous more */
|
---|
| 98 | i2c_device_info query[I2C_MAX_QUERIES];
|
---|
| 99 |
|
---|
| 100 | byte i2cRxData[64];
|
---|
| 101 | boolean isI2CEnabled = false;
|
---|
| 102 | signed char queryIndex = -1;
|
---|
| 103 | // default delay time between i2c read request and Wire.requestFrom()
|
---|
| 104 | unsigned int i2cReadDelayTime = 0;
|
---|
| 105 |
|
---|
| 106 | Servo servos[MAX_SERVOS];
|
---|
| 107 | byte servoPinMap[TOTAL_PINS];
|
---|
| 108 | byte detachedServos[MAX_SERVOS];
|
---|
| 109 | byte detachedServoCount = 0;
|
---|
| 110 | byte servoCount = 0;
|
---|
| 111 |
|
---|
| 112 | boolean isResetting = false;
|
---|
| 113 |
|
---|
| 114 |
|
---|
| 115 | /* utility functions */
|
---|
| 116 | void wireWrite(byte data)
|
---|
| 117 | {
|
---|
| 118 | #if ARDUINO >= 100
|
---|
| 119 | Wire.write((byte)data);
|
---|
| 120 | #else
|
---|
| 121 | Wire.send(data);
|
---|
| 122 | #endif
|
---|
| 123 | }
|
---|
| 124 |
|
---|
| 125 | byte wireRead(void)
|
---|
| 126 | {
|
---|
| 127 | #if ARDUINO >= 100
|
---|
| 128 | return Wire.read();
|
---|
| 129 | #else
|
---|
| 130 | return Wire.receive();
|
---|
| 131 | #endif
|
---|
| 132 | }
|
---|
| 133 |
|
---|
| 134 | /*==============================================================================
|
---|
| 135 | * FUNCTIONS
|
---|
| 136 | *============================================================================*/
|
---|
| 137 |
|
---|
| 138 | void attachServo(byte pin, int minPulse, int maxPulse)
|
---|
| 139 | {
|
---|
| 140 | if (servoCount < MAX_SERVOS) {
|
---|
| 141 | // reuse indexes of detached servos until all have been reallocated
|
---|
| 142 | if (detachedServoCount > 0) {
|
---|
| 143 | servoPinMap[pin] = detachedServos[detachedServoCount - 1];
|
---|
| 144 | if (detachedServoCount > 0) detachedServoCount--;
|
---|
| 145 | } else {
|
---|
| 146 | servoPinMap[pin] = servoCount;
|
---|
| 147 | servoCount++;
|
---|
| 148 | }
|
---|
| 149 | if (minPulse > 0 && maxPulse > 0) {
|
---|
| 150 | servos[servoPinMap[pin]].attach(PIN_TO_DIGITAL(pin), minPulse, maxPulse);
|
---|
| 151 | } else {
|
---|
| 152 | servos[servoPinMap[pin]].attach(PIN_TO_DIGITAL(pin));
|
---|
| 153 | }
|
---|
| 154 | } else {
|
---|
| 155 | Firmata.sendString("Max servos attached");
|
---|
| 156 | }
|
---|
| 157 | }
|
---|
| 158 |
|
---|
| 159 | void detachServo(byte pin)
|
---|
| 160 | {
|
---|
| 161 | servos[servoPinMap[pin]].detach();
|
---|
| 162 | // if we're detaching the last servo, decrement the count
|
---|
| 163 | // otherwise store the index of the detached servo
|
---|
| 164 | if (servoPinMap[pin] == servoCount && servoCount > 0) {
|
---|
| 165 | servoCount--;
|
---|
| 166 | } else if (servoCount > 0) {
|
---|
| 167 | // keep track of detached servos because we want to reuse their indexes
|
---|
| 168 | // before incrementing the count of attached servos
|
---|
| 169 | detachedServoCount++;
|
---|
| 170 | detachedServos[detachedServoCount - 1] = servoPinMap[pin];
|
---|
| 171 | }
|
---|
| 172 |
|
---|
| 173 | servoPinMap[pin] = 255;
|
---|
| 174 | }
|
---|
| 175 |
|
---|
| 176 | void readAndReportData(byte address, int theRegister, byte numBytes, byte stopTX) {
|
---|
| 177 | // allow I2C requests that don't require a register read
|
---|
| 178 | // for example, some devices using an interrupt pin to signify new data available
|
---|
| 179 | // do not always require the register read so upon interrupt you call Wire.requestFrom()
|
---|
| 180 | if (theRegister != I2C_REGISTER_NOT_SPECIFIED) {
|
---|
| 181 | Wire.beginTransmission(address);
|
---|
| 182 | wireWrite((byte)theRegister);
|
---|
| 183 | Wire.endTransmission(stopTX); // default = true
|
---|
| 184 | // do not set a value of 0
|
---|
| 185 | if (i2cReadDelayTime > 0) {
|
---|
| 186 | // delay is necessary for some devices such as WiiNunchuck
|
---|
| 187 | delayMicroseconds(i2cReadDelayTime);
|
---|
| 188 | }
|
---|
| 189 | } else {
|
---|
| 190 | theRegister = 0; // fill the register with a dummy value
|
---|
| 191 | }
|
---|
| 192 |
|
---|
| 193 | Wire.requestFrom(address, numBytes); // all bytes are returned in requestFrom
|
---|
| 194 |
|
---|
| 195 | // check to be sure correct number of bytes were returned by slave
|
---|
| 196 | if (numBytes < Wire.available()) {
|
---|
| 197 | Firmata.sendString("I2C: Too many bytes received");
|
---|
| 198 | } else if (numBytes > Wire.available()) {
|
---|
| 199 | Firmata.sendString("I2C: Too few bytes received");
|
---|
| 200 | }
|
---|
| 201 |
|
---|
| 202 | i2cRxData[0] = address;
|
---|
| 203 | i2cRxData[1] = theRegister;
|
---|
| 204 |
|
---|
| 205 | for (int i = 0; i < numBytes && Wire.available(); i++) {
|
---|
| 206 | i2cRxData[2 + i] = wireRead();
|
---|
| 207 | }
|
---|
| 208 |
|
---|
| 209 | // send slave address, register and received bytes
|
---|
| 210 | Firmata.sendSysex(SYSEX_I2C_REPLY, numBytes + 2, i2cRxData);
|
---|
| 211 | }
|
---|
| 212 |
|
---|
| 213 | void outputPort(byte portNumber, byte portValue, byte forceSend)
|
---|
| 214 | {
|
---|
| 215 | // pins not configured as INPUT are cleared to zeros
|
---|
| 216 | portValue = portValue & portConfigInputs[portNumber];
|
---|
| 217 | // only send if the value is different than previously sent
|
---|
| 218 | if (forceSend || previousPINs[portNumber] != portValue) {
|
---|
| 219 | Firmata.sendDigitalPort(portNumber, portValue);
|
---|
| 220 | previousPINs[portNumber] = portValue;
|
---|
| 221 | }
|
---|
| 222 | }
|
---|
| 223 |
|
---|
| 224 | /* -----------------------------------------------------------------------------
|
---|
| 225 | * check all the active digital inputs for change of state, then add any events
|
---|
| 226 | * to the Serial output queue using Serial.print() */
|
---|
| 227 | void checkDigitalInputs(void)
|
---|
| 228 | {
|
---|
| 229 | /* Using non-looping code allows constants to be given to readPort().
|
---|
| 230 | * The compiler will apply substantial optimizations if the inputs
|
---|
| 231 | * to readPort() are compile-time constants. */
|
---|
| 232 | if (TOTAL_PORTS > 0 && reportPINs[0]) outputPort(0, readPort(0, portConfigInputs[0]), false);
|
---|
| 233 | if (TOTAL_PORTS > 1 && reportPINs[1]) outputPort(1, readPort(1, portConfigInputs[1]), false);
|
---|
| 234 | if (TOTAL_PORTS > 2 && reportPINs[2]) outputPort(2, readPort(2, portConfigInputs[2]), false);
|
---|
| 235 | if (TOTAL_PORTS > 3 && reportPINs[3]) outputPort(3, readPort(3, portConfigInputs[3]), false);
|
---|
| 236 | if (TOTAL_PORTS > 4 && reportPINs[4]) outputPort(4, readPort(4, portConfigInputs[4]), false);
|
---|
| 237 | if (TOTAL_PORTS > 5 && reportPINs[5]) outputPort(5, readPort(5, portConfigInputs[5]), false);
|
---|
| 238 | if (TOTAL_PORTS > 6 && reportPINs[6]) outputPort(6, readPort(6, portConfigInputs[6]), false);
|
---|
| 239 | if (TOTAL_PORTS > 7 && reportPINs[7]) outputPort(7, readPort(7, portConfigInputs[7]), false);
|
---|
| 240 | if (TOTAL_PORTS > 8 && reportPINs[8]) outputPort(8, readPort(8, portConfigInputs[8]), false);
|
---|
| 241 | if (TOTAL_PORTS > 9 && reportPINs[9]) outputPort(9, readPort(9, portConfigInputs[9]), false);
|
---|
| 242 | if (TOTAL_PORTS > 10 && reportPINs[10]) outputPort(10, readPort(10, portConfigInputs[10]), false);
|
---|
| 243 | if (TOTAL_PORTS > 11 && reportPINs[11]) outputPort(11, readPort(11, portConfigInputs[11]), false);
|
---|
| 244 | if (TOTAL_PORTS > 12 && reportPINs[12]) outputPort(12, readPort(12, portConfigInputs[12]), false);
|
---|
| 245 | if (TOTAL_PORTS > 13 && reportPINs[13]) outputPort(13, readPort(13, portConfigInputs[13]), false);
|
---|
| 246 | if (TOTAL_PORTS > 14 && reportPINs[14]) outputPort(14, readPort(14, portConfigInputs[14]), false);
|
---|
| 247 | if (TOTAL_PORTS > 15 && reportPINs[15]) outputPort(15, readPort(15, portConfigInputs[15]), false);
|
---|
| 248 | }
|
---|
| 249 |
|
---|
| 250 | // -----------------------------------------------------------------------------
|
---|
| 251 | /* sets the pin mode to the correct state and sets the relevant bits in the
|
---|
| 252 | * two bit-arrays that track Digital I/O and PWM status
|
---|
| 253 | */
|
---|
| 254 | void setPinModeCallback(byte pin, int mode)
|
---|
| 255 | {
|
---|
| 256 | if (Firmata.getPinMode(pin) == PIN_MODE_IGNORE)
|
---|
| 257 | return;
|
---|
| 258 |
|
---|
| 259 | if (Firmata.getPinMode(pin) == PIN_MODE_I2C && isI2CEnabled && mode != PIN_MODE_I2C) {
|
---|
| 260 | // disable i2c so pins can be used for other functions
|
---|
| 261 | // the following if statements should reconfigure the pins properly
|
---|
| 262 | disableI2CPins();
|
---|
| 263 | }
|
---|
| 264 | if (IS_PIN_DIGITAL(pin) && mode != PIN_MODE_SERVO) {
|
---|
| 265 | if (servoPinMap[pin] < MAX_SERVOS && servos[servoPinMap[pin]].attached()) {
|
---|
| 266 | detachServo(pin);
|
---|
| 267 | }
|
---|
| 268 | }
|
---|
| 269 | if (IS_PIN_ANALOG(pin)) {
|
---|
| 270 | reportAnalogCallback(PIN_TO_ANALOG(pin), mode == PIN_MODE_ANALOG ? 1 : 0); // turn on/off reporting
|
---|
| 271 | }
|
---|
| 272 | if (IS_PIN_DIGITAL(pin)) {
|
---|
| 273 | if (mode == INPUT || mode == PIN_MODE_PULLUP) {
|
---|
| 274 | portConfigInputs[pin / 8] |= (1 << (pin & 7));
|
---|
| 275 | } else {
|
---|
| 276 | portConfigInputs[pin / 8] &= ~(1 << (pin & 7));
|
---|
| 277 | }
|
---|
| 278 | }
|
---|
| 279 | Firmata.setPinState(pin, 0);
|
---|
| 280 | switch (mode) {
|
---|
| 281 | case PIN_MODE_ANALOG:
|
---|
| 282 | if (IS_PIN_ANALOG(pin)) {
|
---|
| 283 | if (IS_PIN_DIGITAL(pin)) {
|
---|
| 284 | pinMode(PIN_TO_DIGITAL(pin), INPUT); // disable output driver
|
---|
| 285 | #if ARDUINO <= 100
|
---|
| 286 | // deprecated since Arduino 1.0.1 - TODO: drop support in Firmata 2.6
|
---|
| 287 | digitalWrite(PIN_TO_DIGITAL(pin), LOW); // disable internal pull-ups
|
---|
| 288 | #endif
|
---|
| 289 | }
|
---|
| 290 | Firmata.setPinMode(pin, PIN_MODE_ANALOG);
|
---|
| 291 | }
|
---|
| 292 | break;
|
---|
| 293 | case INPUT:
|
---|
| 294 | if (IS_PIN_DIGITAL(pin)) {
|
---|
| 295 | pinMode(PIN_TO_DIGITAL(pin), INPUT); // disable output driver
|
---|
| 296 | #if ARDUINO <= 100
|
---|
| 297 | // deprecated since Arduino 1.0.1 - TODO: drop support in Firmata 2.6
|
---|
| 298 | digitalWrite(PIN_TO_DIGITAL(pin), LOW); // disable internal pull-ups
|
---|
| 299 | #endif
|
---|
| 300 | Firmata.setPinMode(pin, INPUT);
|
---|
| 301 | }
|
---|
| 302 | break;
|
---|
| 303 | case PIN_MODE_PULLUP:
|
---|
| 304 | if (IS_PIN_DIGITAL(pin)) {
|
---|
| 305 | pinMode(PIN_TO_DIGITAL(pin), INPUT_PULLUP);
|
---|
| 306 | Firmata.setPinMode(pin, PIN_MODE_PULLUP);
|
---|
| 307 | Firmata.setPinState(pin, 1);
|
---|
| 308 | }
|
---|
| 309 | break;
|
---|
| 310 | case OUTPUT:
|
---|
| 311 | if (IS_PIN_DIGITAL(pin)) {
|
---|
| 312 | digitalWrite(PIN_TO_DIGITAL(pin), LOW); // disable PWM
|
---|
| 313 | pinMode(PIN_TO_DIGITAL(pin), OUTPUT);
|
---|
| 314 | Firmata.setPinMode(pin, OUTPUT);
|
---|
| 315 | }
|
---|
| 316 | break;
|
---|
| 317 | case PIN_MODE_PWM:
|
---|
| 318 | if (IS_PIN_PWM(pin)) {
|
---|
| 319 | pinMode(PIN_TO_PWM(pin), OUTPUT);
|
---|
| 320 | analogWrite(PIN_TO_PWM(pin), 0);
|
---|
| 321 | Firmata.setPinMode(pin, PIN_MODE_PWM);
|
---|
| 322 | }
|
---|
| 323 | break;
|
---|
| 324 | case PIN_MODE_SERVO:
|
---|
| 325 | if (IS_PIN_DIGITAL(pin)) {
|
---|
| 326 | Firmata.setPinMode(pin, PIN_MODE_SERVO);
|
---|
| 327 | if (servoPinMap[pin] == 255 || !servos[servoPinMap[pin]].attached()) {
|
---|
| 328 | // pass -1 for min and max pulse values to use default values set
|
---|
| 329 | // by Servo library
|
---|
| 330 | attachServo(pin, -1, -1);
|
---|
| 331 | }
|
---|
| 332 | }
|
---|
| 333 | break;
|
---|
| 334 | case PIN_MODE_I2C:
|
---|
| 335 | if (IS_PIN_I2C(pin)) {
|
---|
| 336 | // mark the pin as i2c
|
---|
| 337 | // the user must call I2C_CONFIG to enable I2C for a device
|
---|
| 338 | Firmata.setPinMode(pin, PIN_MODE_I2C);
|
---|
| 339 | }
|
---|
| 340 | break;
|
---|
| 341 | case PIN_MODE_SERIAL:
|
---|
| 342 | #ifdef FIRMATA_SERIAL_FEATURE
|
---|
| 343 | serialFeature.handlePinMode(pin, PIN_MODE_SERIAL);
|
---|
| 344 | #endif
|
---|
| 345 | break;
|
---|
| 346 | default:
|
---|
| 347 | Firmata.sendString("Unknown pin mode"); // TODO: put error msgs in EEPROM
|
---|
| 348 | }
|
---|
| 349 | // TODO: save status to EEPROM here, if changed
|
---|
| 350 | }
|
---|
| 351 |
|
---|
| 352 | /*
|
---|
| 353 | * Sets the value of an individual pin. Useful if you want to set a pin value but
|
---|
| 354 | * are not tracking the digital port state.
|
---|
| 355 | * Can only be used on pins configured as OUTPUT.
|
---|
| 356 | * Cannot be used to enable pull-ups on Digital INPUT pins.
|
---|
| 357 | */
|
---|
| 358 | void setPinValueCallback(byte pin, int value)
|
---|
| 359 | {
|
---|
| 360 | if (pin < TOTAL_PINS && IS_PIN_DIGITAL(pin)) {
|
---|
| 361 | if (Firmata.getPinMode(pin) == OUTPUT) {
|
---|
| 362 | Firmata.setPinState(pin, value);
|
---|
| 363 | digitalWrite(PIN_TO_DIGITAL(pin), value);
|
---|
| 364 | }
|
---|
| 365 | }
|
---|
| 366 | }
|
---|
| 367 |
|
---|
| 368 | void analogWriteCallback(byte pin, int value)
|
---|
| 369 | {
|
---|
| 370 | if (pin < TOTAL_PINS) {
|
---|
| 371 | switch (Firmata.getPinMode(pin)) {
|
---|
| 372 | case PIN_MODE_SERVO:
|
---|
| 373 | if (IS_PIN_DIGITAL(pin))
|
---|
| 374 | servos[servoPinMap[pin]].write(value);
|
---|
| 375 | Firmata.setPinState(pin, value);
|
---|
| 376 | break;
|
---|
| 377 | case PIN_MODE_PWM:
|
---|
| 378 | if (IS_PIN_PWM(pin))
|
---|
| 379 | analogWrite(PIN_TO_PWM(pin), value);
|
---|
| 380 | Firmata.setPinState(pin, value);
|
---|
| 381 | break;
|
---|
| 382 | }
|
---|
| 383 | }
|
---|
| 384 | }
|
---|
| 385 |
|
---|
| 386 | void digitalWriteCallback(byte port, int value)
|
---|
| 387 | {
|
---|
| 388 | byte pin, lastPin, pinValue, mask = 1, pinWriteMask = 0;
|
---|
| 389 |
|
---|
| 390 | if (port < TOTAL_PORTS) {
|
---|
| 391 | // create a mask of the pins on this port that are writable.
|
---|
| 392 | lastPin = port * 8 + 8;
|
---|
| 393 | if (lastPin > TOTAL_PINS) lastPin = TOTAL_PINS;
|
---|
| 394 | for (pin = port * 8; pin < lastPin; pin++) {
|
---|
| 395 | // do not disturb non-digital pins (eg, Rx & Tx)
|
---|
| 396 | if (IS_PIN_DIGITAL(pin)) {
|
---|
| 397 | // do not touch pins in PWM, ANALOG, SERVO or other modes
|
---|
| 398 | if (Firmata.getPinMode(pin) == OUTPUT || Firmata.getPinMode(pin) == INPUT) {
|
---|
| 399 | pinValue = ((byte)value & mask) ? 1 : 0;
|
---|
| 400 | if (Firmata.getPinMode(pin) == OUTPUT) {
|
---|
| 401 | pinWriteMask |= mask;
|
---|
| 402 | } else if (Firmata.getPinMode(pin) == INPUT && pinValue == 1 && Firmata.getPinState(pin) != 1) {
|
---|
| 403 | // only handle INPUT here for backwards compatibility
|
---|
| 404 | #if ARDUINO > 100
|
---|
| 405 | pinMode(pin, INPUT_PULLUP);
|
---|
| 406 | #else
|
---|
| 407 | // only write to the INPUT pin to enable pullups if Arduino v1.0.0 or earlier
|
---|
| 408 | pinWriteMask |= mask;
|
---|
| 409 | #endif
|
---|
| 410 | }
|
---|
| 411 | Firmata.setPinState(pin, pinValue);
|
---|
| 412 | }
|
---|
| 413 | }
|
---|
| 414 | mask = mask << 1;
|
---|
| 415 | }
|
---|
| 416 | writePort(port, (byte)value, pinWriteMask);
|
---|
| 417 | }
|
---|
| 418 | }
|
---|
| 419 |
|
---|
| 420 |
|
---|
| 421 | // -----------------------------------------------------------------------------
|
---|
| 422 | /* sets bits in a bit array (int) to toggle the reporting of the analogIns
|
---|
| 423 | */
|
---|
| 424 | //void FirmataClass::setAnalogPinReporting(byte pin, byte state) {
|
---|
| 425 | //}
|
---|
| 426 | void reportAnalogCallback(byte analogPin, int value)
|
---|
| 427 | {
|
---|
| 428 | if (analogPin < TOTAL_ANALOG_PINS) {
|
---|
| 429 | if (value == 0) {
|
---|
| 430 | analogInputsToReport = analogInputsToReport & ~ (1 << analogPin);
|
---|
| 431 | } else {
|
---|
| 432 | analogInputsToReport = analogInputsToReport | (1 << analogPin);
|
---|
| 433 | // prevent during system reset or all analog pin values will be reported
|
---|
| 434 | // which may report noise for unconnected analog pins
|
---|
| 435 | if (!isResetting) {
|
---|
| 436 | // Send pin value immediately. This is helpful when connected via
|
---|
| 437 | // ethernet, wi-fi or bluetooth so pin states can be known upon
|
---|
| 438 | // reconnecting.
|
---|
| 439 | Firmata.sendAnalog(analogPin, analogRead(analogPin));
|
---|
| 440 | }
|
---|
| 441 | }
|
---|
| 442 | }
|
---|
| 443 | // TODO: save status to EEPROM here, if changed
|
---|
| 444 | }
|
---|
| 445 |
|
---|
| 446 | void reportDigitalCallback(byte port, int value)
|
---|
| 447 | {
|
---|
| 448 | if (port < TOTAL_PORTS) {
|
---|
| 449 | reportPINs[port] = (byte)value;
|
---|
| 450 | // Send port value immediately. This is helpful when connected via
|
---|
| 451 | // ethernet, wi-fi or bluetooth so pin states can be known upon
|
---|
| 452 | // reconnecting.
|
---|
| 453 | if (value) outputPort(port, readPort(port, portConfigInputs[port]), true);
|
---|
| 454 | }
|
---|
| 455 | // do not disable analog reporting on these 8 pins, to allow some
|
---|
| 456 | // pins used for digital, others analog. Instead, allow both types
|
---|
| 457 | // of reporting to be enabled, but check if the pin is configured
|
---|
| 458 | // as analog when sampling the analog inputs. Likewise, while
|
---|
| 459 | // scanning digital pins, portConfigInputs will mask off values from any
|
---|
| 460 | // pins configured as analog
|
---|
| 461 | }
|
---|
| 462 |
|
---|
| 463 | /*==============================================================================
|
---|
| 464 | * SYSEX-BASED commands
|
---|
| 465 | *============================================================================*/
|
---|
| 466 |
|
---|
| 467 | void sysexCallback(byte command, byte argc, byte *argv)
|
---|
| 468 | {
|
---|
| 469 | byte mode;
|
---|
| 470 | byte stopTX;
|
---|
| 471 | byte slaveAddress;
|
---|
| 472 | byte data;
|
---|
| 473 | int slaveRegister;
|
---|
| 474 | unsigned int delayTime;
|
---|
| 475 |
|
---|
| 476 | switch (command) {
|
---|
| 477 | case I2C_REQUEST:
|
---|
| 478 | mode = argv[1] & I2C_READ_WRITE_MODE_MASK;
|
---|
| 479 | if (argv[1] & I2C_10BIT_ADDRESS_MODE_MASK) {
|
---|
| 480 | Firmata.sendString("10-bit addressing not supported");
|
---|
| 481 | return;
|
---|
| 482 | }
|
---|
| 483 | else {
|
---|
| 484 | slaveAddress = argv[0];
|
---|
| 485 | }
|
---|
| 486 |
|
---|
| 487 | // need to invert the logic here since 0 will be default for client
|
---|
| 488 | // libraries that have not updated to add support for restart tx
|
---|
| 489 | if (argv[1] & I2C_END_TX_MASK) {
|
---|
| 490 | stopTX = I2C_RESTART_TX;
|
---|
| 491 | }
|
---|
| 492 | else {
|
---|
| 493 | stopTX = I2C_STOP_TX; // default
|
---|
| 494 | }
|
---|
| 495 |
|
---|
| 496 | switch (mode) {
|
---|
| 497 | case I2C_WRITE:
|
---|
| 498 | Wire.beginTransmission(slaveAddress);
|
---|
| 499 | for (byte i = 2; i < argc; i += 2) {
|
---|
| 500 | data = argv[i] + (argv[i + 1] << 7);
|
---|
| 501 | wireWrite(data);
|
---|
| 502 | }
|
---|
| 503 | Wire.endTransmission();
|
---|
| 504 | delayMicroseconds(70);
|
---|
| 505 | break;
|
---|
| 506 | case I2C_READ:
|
---|
| 507 | if (argc == 6) {
|
---|
| 508 | // a slave register is specified
|
---|
| 509 | slaveRegister = argv[2] + (argv[3] << 7);
|
---|
| 510 | data = argv[4] + (argv[5] << 7); // bytes to read
|
---|
| 511 | }
|
---|
| 512 | else {
|
---|
| 513 | // a slave register is NOT specified
|
---|
| 514 | slaveRegister = I2C_REGISTER_NOT_SPECIFIED;
|
---|
| 515 | data = argv[2] + (argv[3] << 7); // bytes to read
|
---|
| 516 | }
|
---|
| 517 | readAndReportData(slaveAddress, (int)slaveRegister, data, stopTX);
|
---|
| 518 | break;
|
---|
| 519 | case I2C_READ_CONTINUOUSLY:
|
---|
| 520 | if ((queryIndex + 1) >= I2C_MAX_QUERIES) {
|
---|
| 521 | // too many queries, just ignore
|
---|
| 522 | Firmata.sendString("too many queries");
|
---|
| 523 | break;
|
---|
| 524 | }
|
---|
| 525 | if (argc == 6) {
|
---|
| 526 | // a slave register is specified
|
---|
| 527 | slaveRegister = argv[2] + (argv[3] << 7);
|
---|
| 528 | data = argv[4] + (argv[5] << 7); // bytes to read
|
---|
| 529 | }
|
---|
| 530 | else {
|
---|
| 531 | // a slave register is NOT specified
|
---|
| 532 | slaveRegister = (int)I2C_REGISTER_NOT_SPECIFIED;
|
---|
| 533 | data = argv[2] + (argv[3] << 7); // bytes to read
|
---|
| 534 | }
|
---|
| 535 | queryIndex++;
|
---|
| 536 | query[queryIndex].addr = slaveAddress;
|
---|
| 537 | query[queryIndex].reg = slaveRegister;
|
---|
| 538 | query[queryIndex].bytes = data;
|
---|
| 539 | query[queryIndex].stopTX = stopTX;
|
---|
| 540 | break;
|
---|
| 541 | case I2C_STOP_READING:
|
---|
| 542 | byte queryIndexToSkip;
|
---|
| 543 | // if read continuous mode is enabled for only 1 i2c device, disable
|
---|
| 544 | // read continuous reporting for that device
|
---|
| 545 | if (queryIndex <= 0) {
|
---|
| 546 | queryIndex = -1;
|
---|
| 547 | } else {
|
---|
| 548 | queryIndexToSkip = 0;
|
---|
| 549 | // if read continuous mode is enabled for multiple devices,
|
---|
| 550 | // determine which device to stop reading and remove it's data from
|
---|
| 551 | // the array, shifiting other array data to fill the space
|
---|
| 552 | for (byte i = 0; i < queryIndex + 1; i++) {
|
---|
| 553 | if (query[i].addr == slaveAddress) {
|
---|
| 554 | queryIndexToSkip = i;
|
---|
| 555 | break;
|
---|
| 556 | }
|
---|
| 557 | }
|
---|
| 558 |
|
---|
| 559 | for (byte i = queryIndexToSkip; i < queryIndex + 1; i++) {
|
---|
| 560 | if (i < I2C_MAX_QUERIES) {
|
---|
| 561 | query[i].addr = query[i + 1].addr;
|
---|
| 562 | query[i].reg = query[i + 1].reg;
|
---|
| 563 | query[i].bytes = query[i + 1].bytes;
|
---|
| 564 | query[i].stopTX = query[i + 1].stopTX;
|
---|
| 565 | }
|
---|
| 566 | }
|
---|
| 567 | queryIndex--;
|
---|
| 568 | }
|
---|
| 569 | break;
|
---|
| 570 | default:
|
---|
| 571 | break;
|
---|
| 572 | }
|
---|
| 573 | break;
|
---|
| 574 | case I2C_CONFIG:
|
---|
| 575 | delayTime = (argv[0] + (argv[1] << 7));
|
---|
| 576 |
|
---|
| 577 | if (delayTime > 0) {
|
---|
| 578 | i2cReadDelayTime = delayTime;
|
---|
| 579 | }
|
---|
| 580 |
|
---|
| 581 | if (!isI2CEnabled) {
|
---|
| 582 | enableI2CPins();
|
---|
| 583 | }
|
---|
| 584 |
|
---|
| 585 | break;
|
---|
| 586 | case SERVO_CONFIG:
|
---|
| 587 | if (argc > 4) {
|
---|
| 588 | // these vars are here for clarity, they'll optimized away by the compiler
|
---|
| 589 | byte pin = argv[0];
|
---|
| 590 | int minPulse = argv[1] + (argv[2] << 7);
|
---|
| 591 | int maxPulse = argv[3] + (argv[4] << 7);
|
---|
| 592 |
|
---|
| 593 | if (IS_PIN_DIGITAL(pin)) {
|
---|
| 594 | if (servoPinMap[pin] < MAX_SERVOS && servos[servoPinMap[pin]].attached()) {
|
---|
| 595 | detachServo(pin);
|
---|
| 596 | }
|
---|
| 597 | attachServo(pin, minPulse, maxPulse);
|
---|
| 598 | setPinModeCallback(pin, PIN_MODE_SERVO);
|
---|
| 599 | }
|
---|
| 600 | }
|
---|
| 601 | break;
|
---|
| 602 | case SAMPLING_INTERVAL:
|
---|
| 603 | if (argc > 1) {
|
---|
| 604 | samplingInterval = argv[0] + (argv[1] << 7);
|
---|
| 605 | if (samplingInterval < MINIMUM_SAMPLING_INTERVAL) {
|
---|
| 606 | samplingInterval = MINIMUM_SAMPLING_INTERVAL;
|
---|
| 607 | }
|
---|
| 608 | } else {
|
---|
| 609 | //Firmata.sendString("Not enough data");
|
---|
| 610 | }
|
---|
| 611 | break;
|
---|
| 612 | case EXTENDED_ANALOG:
|
---|
| 613 | if (argc > 1) {
|
---|
| 614 | int val = argv[1];
|
---|
| 615 | if (argc > 2) val |= (argv[2] << 7);
|
---|
| 616 | if (argc > 3) val |= (argv[3] << 14);
|
---|
| 617 | analogWriteCallback(argv[0], val);
|
---|
| 618 | }
|
---|
| 619 | break;
|
---|
| 620 | case CAPABILITY_QUERY:
|
---|
| 621 | Firmata.write(START_SYSEX);
|
---|
| 622 | Firmata.write(CAPABILITY_RESPONSE);
|
---|
| 623 | for (byte pin = 0; pin < TOTAL_PINS; pin++) {
|
---|
| 624 | if (IS_PIN_DIGITAL(pin)) {
|
---|
| 625 | Firmata.write((byte)INPUT);
|
---|
| 626 | Firmata.write(1);
|
---|
| 627 | Firmata.write((byte)PIN_MODE_PULLUP);
|
---|
| 628 | Firmata.write(1);
|
---|
| 629 | Firmata.write((byte)OUTPUT);
|
---|
| 630 | Firmata.write(1);
|
---|
| 631 | }
|
---|
| 632 | if (IS_PIN_ANALOG(pin)) {
|
---|
| 633 | Firmata.write(PIN_MODE_ANALOG);
|
---|
| 634 | Firmata.write(10); // 10 = 10-bit resolution
|
---|
| 635 | }
|
---|
| 636 | if (IS_PIN_PWM(pin)) {
|
---|
| 637 | Firmata.write(PIN_MODE_PWM);
|
---|
| 638 | Firmata.write(8); // 8 = 8-bit resolution
|
---|
| 639 | }
|
---|
| 640 | if (IS_PIN_DIGITAL(pin)) {
|
---|
| 641 | Firmata.write(PIN_MODE_SERVO);
|
---|
| 642 | Firmata.write(14);
|
---|
| 643 | }
|
---|
| 644 | if (IS_PIN_I2C(pin)) {
|
---|
| 645 | Firmata.write(PIN_MODE_I2C);
|
---|
| 646 | Firmata.write(1); // TODO: could assign a number to map to SCL or SDA
|
---|
| 647 | }
|
---|
| 648 | #ifdef FIRMATA_SERIAL_FEATURE
|
---|
| 649 | serialFeature.handleCapability(pin);
|
---|
| 650 | #endif
|
---|
| 651 | Firmata.write(127);
|
---|
| 652 | }
|
---|
| 653 | Firmata.write(END_SYSEX);
|
---|
| 654 | break;
|
---|
| 655 | case PIN_STATE_QUERY:
|
---|
| 656 | if (argc > 0) {
|
---|
| 657 | byte pin = argv[0];
|
---|
| 658 | Firmata.write(START_SYSEX);
|
---|
| 659 | Firmata.write(PIN_STATE_RESPONSE);
|
---|
| 660 | Firmata.write(pin);
|
---|
| 661 | if (pin < TOTAL_PINS) {
|
---|
| 662 | Firmata.write(Firmata.getPinMode(pin));
|
---|
| 663 | Firmata.write((byte)Firmata.getPinState(pin) & 0x7F);
|
---|
| 664 | if (Firmata.getPinState(pin) & 0xFF80) Firmata.write((byte)(Firmata.getPinState(pin) >> 7) & 0x7F);
|
---|
| 665 | if (Firmata.getPinState(pin) & 0xC000) Firmata.write((byte)(Firmata.getPinState(pin) >> 14) & 0x7F);
|
---|
| 666 | }
|
---|
| 667 | Firmata.write(END_SYSEX);
|
---|
| 668 | }
|
---|
| 669 | break;
|
---|
| 670 | case ANALOG_MAPPING_QUERY:
|
---|
| 671 | Firmata.write(START_SYSEX);
|
---|
| 672 | Firmata.write(ANALOG_MAPPING_RESPONSE);
|
---|
| 673 | for (byte pin = 0; pin < TOTAL_PINS; pin++) {
|
---|
| 674 | Firmata.write(IS_PIN_ANALOG(pin) ? PIN_TO_ANALOG(pin) : 127);
|
---|
| 675 | }
|
---|
| 676 | Firmata.write(END_SYSEX);
|
---|
| 677 | break;
|
---|
| 678 |
|
---|
| 679 | case SERIAL_MESSAGE:
|
---|
| 680 | #ifdef FIRMATA_SERIAL_FEATURE
|
---|
| 681 | serialFeature.handleSysex(command, argc, argv);
|
---|
| 682 | #endif
|
---|
| 683 | break;
|
---|
| 684 | }
|
---|
| 685 | }
|
---|
| 686 |
|
---|
| 687 | void enableI2CPins()
|
---|
| 688 | {
|
---|
| 689 | byte i;
|
---|
| 690 | // is there a faster way to do this? would probaby require importing
|
---|
| 691 | // Arduino.h to get SCL and SDA pins
|
---|
| 692 | for (i = 0; i < TOTAL_PINS; i++) {
|
---|
| 693 | if (IS_PIN_I2C(i)) {
|
---|
| 694 | // mark pins as i2c so they are ignore in non i2c data requests
|
---|
| 695 | setPinModeCallback(i, PIN_MODE_I2C);
|
---|
| 696 | }
|
---|
| 697 | }
|
---|
| 698 |
|
---|
| 699 | isI2CEnabled = true;
|
---|
| 700 |
|
---|
| 701 | Wire.begin();
|
---|
| 702 | }
|
---|
| 703 |
|
---|
| 704 | /* disable the i2c pins so they can be used for other functions */
|
---|
| 705 | void disableI2CPins() {
|
---|
| 706 | isI2CEnabled = false;
|
---|
| 707 | // disable read continuous mode for all devices
|
---|
| 708 | queryIndex = -1;
|
---|
| 709 | }
|
---|
| 710 |
|
---|
| 711 | /*==============================================================================
|
---|
| 712 | * SETUP()
|
---|
| 713 | *============================================================================*/
|
---|
| 714 |
|
---|
| 715 | void systemResetCallback()
|
---|
| 716 | {
|
---|
| 717 | isResetting = true;
|
---|
| 718 |
|
---|
| 719 | // initialize a defalt state
|
---|
| 720 | // TODO: option to load config from EEPROM instead of default
|
---|
| 721 |
|
---|
| 722 | #ifdef FIRMATA_SERIAL_FEATURE
|
---|
| 723 | serialFeature.reset();
|
---|
| 724 | #endif
|
---|
| 725 |
|
---|
| 726 | if (isI2CEnabled) {
|
---|
| 727 | disableI2CPins();
|
---|
| 728 | }
|
---|
| 729 |
|
---|
| 730 | for (byte i = 0; i < TOTAL_PORTS; i++) {
|
---|
| 731 | reportPINs[i] = false; // by default, reporting off
|
---|
| 732 | portConfigInputs[i] = 0; // until activated
|
---|
| 733 | previousPINs[i] = 0;
|
---|
| 734 | }
|
---|
| 735 |
|
---|
| 736 | for (byte i = 0; i < TOTAL_PINS; i++) {
|
---|
| 737 | // pins with analog capability default to analog input
|
---|
| 738 | // otherwise, pins default to digital output
|
---|
| 739 | if (IS_PIN_ANALOG(i)) {
|
---|
| 740 | // turns off pullup, configures everything
|
---|
| 741 | setPinModeCallback(i, PIN_MODE_ANALOG);
|
---|
| 742 | } else if (IS_PIN_DIGITAL(i)) {
|
---|
| 743 | // sets the output to 0, configures portConfigInputs
|
---|
| 744 | setPinModeCallback(i, OUTPUT);
|
---|
| 745 | }
|
---|
| 746 |
|
---|
| 747 | servoPinMap[i] = 255;
|
---|
| 748 | }
|
---|
| 749 | // by default, do not report any analog inputs
|
---|
| 750 | analogInputsToReport = 0;
|
---|
| 751 |
|
---|
| 752 | detachedServoCount = 0;
|
---|
| 753 | servoCount = 0;
|
---|
| 754 |
|
---|
| 755 | /* send digital inputs to set the initial state on the host computer,
|
---|
| 756 | * since once in the loop(), this firmware will only send on change */
|
---|
| 757 | /*
|
---|
| 758 | TODO: this can never execute, since no pins default to digital input
|
---|
| 759 | but it will be needed when/if we support EEPROM stored config
|
---|
| 760 | for (byte i=0; i < TOTAL_PORTS; i++) {
|
---|
| 761 | outputPort(i, readPort(i, portConfigInputs[i]), true);
|
---|
| 762 | }
|
---|
| 763 | */
|
---|
| 764 | isResetting = false;
|
---|
| 765 | }
|
---|
| 766 |
|
---|
| 767 | void setup()
|
---|
| 768 | {
|
---|
| 769 | Firmata.setFirmwareVersion(FIRMATA_FIRMWARE_MAJOR_VERSION, FIRMATA_FIRMWARE_MINOR_VERSION);
|
---|
| 770 |
|
---|
| 771 | Firmata.attach(ANALOG_MESSAGE, analogWriteCallback);
|
---|
| 772 | Firmata.attach(DIGITAL_MESSAGE, digitalWriteCallback);
|
---|
| 773 | Firmata.attach(REPORT_ANALOG, reportAnalogCallback);
|
---|
| 774 | Firmata.attach(REPORT_DIGITAL, reportDigitalCallback);
|
---|
| 775 | Firmata.attach(SET_PIN_MODE, setPinModeCallback);
|
---|
| 776 | Firmata.attach(SET_DIGITAL_PIN_VALUE, setPinValueCallback);
|
---|
| 777 | Firmata.attach(START_SYSEX, sysexCallback);
|
---|
| 778 | Firmata.attach(SYSTEM_RESET, systemResetCallback);
|
---|
| 779 |
|
---|
| 780 | // Save a couple of seconds by disabling the startup blink sequence.
|
---|
| 781 | Firmata.disableBlinkVersion();
|
---|
| 782 |
|
---|
| 783 | // to use a port other than Serial, such as Serial1 on an Arduino Leonardo or Mega,
|
---|
| 784 | // Call begin(baud) on the alternate serial port and pass it to Firmata to begin like this:
|
---|
| 785 | // Serial1.begin(57600);
|
---|
| 786 | // Firmata.begin(Serial1);
|
---|
| 787 | // However do not do this if you are using SERIAL_MESSAGE
|
---|
| 788 |
|
---|
| 789 | Firmata.begin(57600);
|
---|
| 790 | while (!Serial) {
|
---|
| 791 | ; // wait for serial port to connect. Needed for ATmega32u4-based boards and Arduino 101
|
---|
| 792 | }
|
---|
| 793 |
|
---|
| 794 | systemResetCallback(); // reset to default config
|
---|
| 795 | }
|
---|
| 796 |
|
---|
| 797 | /*==============================================================================
|
---|
| 798 | * LOOP()
|
---|
| 799 | *============================================================================*/
|
---|
| 800 | void loop()
|
---|
| 801 | {
|
---|
| 802 | byte pin, analogPin;
|
---|
| 803 |
|
---|
| 804 | /* DIGITALREAD - as fast as possible, check for changes and output them to the
|
---|
| 805 | * FTDI buffer using Serial.print() */
|
---|
| 806 | checkDigitalInputs();
|
---|
| 807 |
|
---|
| 808 | /* STREAMREAD - processing incoming messagse as soon as possible, while still
|
---|
| 809 | * checking digital inputs. */
|
---|
| 810 | while (Firmata.available())
|
---|
| 811 | Firmata.processInput();
|
---|
| 812 |
|
---|
| 813 | // TODO - ensure that Stream buffer doesn't go over 60 bytes
|
---|
| 814 |
|
---|
| 815 | currentMillis = millis();
|
---|
| 816 | if (currentMillis - previousMillis > samplingInterval) {
|
---|
| 817 | previousMillis += samplingInterval;
|
---|
| 818 | /* ANALOGREAD - do all analogReads() at the configured sampling interval */
|
---|
| 819 | for (pin = 0; pin < TOTAL_PINS; pin++) {
|
---|
| 820 | if (IS_PIN_ANALOG(pin) && Firmata.getPinMode(pin) == PIN_MODE_ANALOG) {
|
---|
| 821 | analogPin = PIN_TO_ANALOG(pin);
|
---|
| 822 | if (analogInputsToReport & (1 << analogPin)) {
|
---|
| 823 | Firmata.sendAnalog(analogPin, analogRead(analogPin));
|
---|
| 824 | }
|
---|
| 825 | }
|
---|
| 826 | }
|
---|
| 827 | // report i2c data for all device with read continuous mode enabled
|
---|
| 828 | if (queryIndex > -1) {
|
---|
| 829 | for (byte i = 0; i < queryIndex + 1; i++) {
|
---|
| 830 | readAndReportData(query[i].addr, query[i].reg, query[i].bytes, query[i].stopTX);
|
---|
| 831 | }
|
---|
| 832 | }
|
---|
| 833 | }
|
---|
| 834 |
|
---|
| 835 | #ifdef FIRMATA_SERIAL_FEATURE
|
---|
| 836 | serialFeature.update();
|
---|
| 837 | #endif
|
---|
| 838 | }
|
---|