[224] | 1 | /*==============================================================================
|
---|
| 2 | * NETWORK CONFIGURATION
|
---|
| 3 | *
|
---|
| 4 | * You must configure your particular hardware. Follow the steps below.
|
---|
| 5 | *
|
---|
| 6 | * Currently StandardFirmataEthernetPlus is configured as a client. An option to
|
---|
| 7 | * configure as a server may be added in the future.
|
---|
| 8 | *============================================================================*/
|
---|
| 9 |
|
---|
| 10 | /*
|
---|
| 11 | * Only WIZ5100-based shields and boards are currently supported for
|
---|
| 12 | * StandardFirmataEthernetPlus.
|
---|
| 13 | */
|
---|
| 14 | #define WIZ5100_ETHERNET
|
---|
| 15 |
|
---|
| 16 | #ifdef WIZ5100_ETHERNET
|
---|
| 17 | #include <SPI.h>
|
---|
| 18 | #include <Ethernet.h>
|
---|
| 19 | EthernetClient client;
|
---|
| 20 | #endif
|
---|
| 21 |
|
---|
| 22 | // STEP 1 [REQUIRED for all boards and shields]
|
---|
| 23 | // replace with IP of the server you want to connect to, comment out if using 'remote_host'
|
---|
| 24 | #define remote_ip IPAddress(10, 0, 0, 3)
|
---|
| 25 | // *** REMOTE HOST IS NOT YET WORKING ***
|
---|
| 26 | // replace with hostname of server you want to connect to, comment out if using 'remote_ip'
|
---|
| 27 | // #define remote_host "server.local"
|
---|
| 28 |
|
---|
| 29 | // STEP 2 [REQUIRED]
|
---|
| 30 | // Replace with the port that your server is listening on
|
---|
| 31 | #define remote_port 3030
|
---|
| 32 |
|
---|
| 33 | // STEP 3 [REQUIRED unless using DHCP]
|
---|
| 34 | // Replace with your board or ethernet shield's IP address
|
---|
| 35 | // Comment out if you want to use DHCP
|
---|
| 36 | #define local_ip IPAddress(10, 0, 0, 15)
|
---|
| 37 |
|
---|
| 38 | // STEP 4 [REQUIRED]
|
---|
| 39 | // replace with ethernet shield mac. Must be unique for your network
|
---|
| 40 | const byte mac[] = {0x90, 0xA2, 0xDA, 0x00, 0x53, 0xE5};
|
---|
| 41 |
|
---|
| 42 | /*==============================================================================
|
---|
| 43 | * CONFIGURATION ERROR CHECK (don't change anything here)
|
---|
| 44 | *============================================================================*/
|
---|
| 45 |
|
---|
| 46 | #if defined remote_ip && defined remote_host
|
---|
| 47 | #error "cannot define both remote_ip and remote_host at the same time in ethernetConfig.h"
|
---|
| 48 | #endif
|
---|
| 49 |
|
---|
| 50 | /*==============================================================================
|
---|
| 51 | * PIN IGNORE MACROS (don't change anything here)
|
---|
| 52 | *============================================================================*/
|
---|
| 53 |
|
---|
| 54 | // ignore SPI pins, pin 10 (Ethernet SS) and pin 4 (SS for SD-Card on Ethernet shield)
|
---|
| 55 | #define IS_IGNORE_ETHERNET_SHIELD(p) ((IS_PIN_SPI(p) || (p) == 4) || (p) == 10)
|
---|